How to Fill Water Tanks

How to Fill Water Tanks

Note: To ensure the normal operation of the One Laser XT model, please note that the cold water pump equipped with this device is used to cool the glass tube. The water in the water tank of the water pump has been drained at the factory. If it is powered on directly without adding pure water, it will directly cause electrical failure. Therefore, after receiving the device, please add pure water to the water tank of the water pump as soon as possible to ensure the safe operation of the device.



1.Preparation

①. Consumable preparation

  One Laser XT model device*1，M2 hexagon wrench

②. Debug software

   None

2.Operation step

①.Remove the back cover of the device

Note:The left door of the device needs to be removed at the same time.

  1. Use an M2 hexagonal wrench to remove the hexagonal screws on the back cover and left door of the device and place them together.                                                                                                                                                                                                                                                                                  
  1. Take out the back cover of the device                                                                                                                                                                                                                                                                                                                                                 

    ②.Fill the water tank with pure water

    Note: Using pure water as cooling water can prevent scaling and corrosion, improve cooling efficiency, and inhibit the growth of microorganisms, thereby effectively protecting the equipment, ensuring its stable operation and extending its service life.                                                                                                                 

    • Find the location of the water tank                                                                                                                                                                                                             
    • Open the water filling cap on the top of the water tank and pour in about 790ml of pure water.
    •                                                                                                                             Older models；
      • Start the equipment, after the pump is started, immediately pour in about 790ml of pure water, observe while pouring, until the water in the storage tank flows into the glass tube .
        
      • After has flowed into the tube, you need to add another 150ml or so of pure water, and once you have done so, put the filler cap back on and tighten it.
                      
                    New model:

                The new model of the device in the water tank outside the water level detection, to prevent the device pump dry burning led to damage   

      
               
              
  • Pour in about 790ml of pure water, start the device and wait for the water to flow in, after flowing into the tube, you need to add another 150ml or so of pure water, after joining, put the water filler cap back on and tighten it.
                   
     

③.Antifreeze ratio

Note: To ensure the normal operation of the device in a low temperature environment, when the indoor temperature drops below 10 degrees Celsius, be sure to add antifreeze to the water tank in proportion. If antifreeze is not added, the low temperature may cause abnormalities in the glass tube of the device, thereby affecting the normal operation of the device.

  • Ratio diagram：                                                                                                                                                                                                                                                                                                                                                                                   
    • According to the ratio of pure water and antifreeze shown in the figure above, pour in pure water first, then add antifreeze
    • Care Instructions：

    1. The antifreeze fluid will deteriorate to a certain extent when it is used for a long time. After the antifreeze fluid deteriorates, it will be more corrosive and the viscosity will also change, so it needs to be replaced regularly. The frequency of replacement we recommend is to change the water once every 2-3 months (at room temperature). When the ambient temperature starts to rise and the sub-zero temperature is lifted, the circulating cooling water can be replaced with softened water such as distilled water or purified water.


    2. Try to use the same brand of antifreeze. Even if the main components of different types of antifreeze are the same, their additive formulas will be different. It is not advisable to mix them to avoid chemical reactions, precipitation or bubbles.


    3. If laser machine will not be used for a long time, the water inside of laser tube, chiller and water pipes should be drained out, especially for glass laser tube. If buyer did not carry out our instruction, any broken of laser tube caused by this will not be guaranteed.


    ④.Post-Processing

    • After the water tank is filled with water, please reinstall the rear cover and side door of the device.                                                                                              

    • Related Articles

    • Unboxing the X Series

      Unbox Step Cut cable tie. After removing the carton packaging, you can move the machine to your workbench. Remove the protective film. Remove all items included and remove the inner foam. Confirm all items. Disassemble the back box and add distilled ...

    • OneLaser Approved Antifreeze

      Based on our testing and research, we recommend adding the two antifreeze solutions recommended in this article to the chiller during winter. Please read the instructions carefully and make adequate preparations before use 1. Turning all machine off ...

    • Laser Replacement

      Note: 1.The following operations should be performed after power disconnection. 2.Please keep the removed screws properly to avoid loss. Disassembly of the Enclosure Both XT and XRF models require disassembly of the casing Use an M2 hex wrench to ...

    • Maintenance Guide

      Optical Maintenance Tool Requirements Lens cleaner、Q-tip、hex key If the provided cleaning cleaner runs out, we recommend using absolute ethanol to clean the lens. To avoid damaging the lens coating, please do not use isopropyl alcohol. If the ...

    • Laser replacement

      Notes: 1.Before operation, the power must be disconnected, otherwise there is a risk of electric shock. 2.Please keep the screws that are removed properly to avoid losing them. Tools Required: Hex wrench,flathead screwdriver,Phillips screwdriver,door ...