One Laser Hydra Touchscreen Function Introduction

One Laser Hydra Touchscreen Function Introduction

Introduction：

This document offers a comprehensive guide to the functions of each button on the control panel, ensuring a thorough understanding of their operations.

1.How to use the display


1. Z axis button: control the table to move in Z-axis.

2. Direction button: control the laser head to move in X and Y axis.

3. U-axis button, controls the rotation of the rotary fixture.

4. Esc button: exit the current state.

5. Pause/Start button: pause/start the current job


2.Home page

  


1. Preview image: preview effect of the current file.

2. Name: The name of the file.

3. Power setting: Max power and min power.

4. Working time: The running time of this job.

5. Speed setting: Running speed of your job.

6. Coordinates: The coordinate of origin you set.

7. Processing progress: Check the processing status

of the job.

8. IP address: Show the IP address of machine.

9. Air assist: It will be displayed when the machine is in

standard mode. Intelligent mode as default settings.

10. Exhaust: It will be displayed when the machine is in

standard mode.

11. Water protection: Only for DC tubes.

12. Door protection status: All doors are closed when

it’s gray. It’s red when a door is opened.



3.Manual page

This screen will show the manual buttons and the functions for adjusting the speed of the axes.



1. Nudge: Set the travel distance when moving each axis manually.

2. Target position: Set a coordinate, then the laser

head will move to here.

3. Mobile mode: Change the mode.

4. Lock button: Lock or unlock the manual buttons.

5. Reset button: To reset X/Y axes.

6. Z axis button: control the table to move in Z-axis

7. Direction button: control the laser head to move in X and Y axis.

8. Spare button



4.File page

This screen will display the file details, where you can select the corresponding file and modify the speed or power parameters of the file.    

Settings: check more settings of file.

Select and hold a file for 2 seconds to select it to run.

5.Menu page

This interface will show more features such as language, Internet and so on.

1. Language: Change the language of panel.

2. Internet: Set the IP address.

3. Diagnostics: the “ Diagnostics ” interface shows some system input information, such as limiter status,

and the status of the door protection etc.


4. U disk: Upload files via U-disk.

5. External Device: Switch the intelligent and standard mode. And set delay time for exhaust and air assist time.


6. Lamp: Adjust the brightness of led lamp.

7. Alignment: Check and adjust the laser beam.

8. Axes Reset: Reset all axes.

9. Multi Origins: Set multi origins.

10. Factory Reset: Reset the vendor settings.

11. Factory Backup: Set the current setting as vendor settings.

12. System Info: Check all info of your laser.



6.Others

 Auto focus button: Click this button to auto focus after placing the materials on working bed.

Origin button: Click this button after selecting a file.



Frame button: Click it to run a frame of your file after setting an origin


    • Related Articles

    • How to use One Laser Hydra camera

      ntroduction: The purpose of this document is to instruct users on how to connect, calibrate and use the One Laser Hydra series camera. Preparation USB cable*1, PC*1, USB flash drive*1, Lightburn software Connecting the machine and the camera 1. ...

    • One Laser Hydra Switching Dual Light Source Tutorial

      Note: When configuring dual light sources in the software, make sure that the two lasers are of different types. If the two lasers are of the same type, the motherboard may mistakenly identify them as dual-tube mode, causing both lasers to start ...

    • Device Disassembly Guide

      Note: When the width of elevator doors, room doors, or other passages is insufficient for the device to pass through, you can disassemble some of the outer shell components to reduce the width requirement for the device. Personnel Requirements: A ...

    • How to switch between different focusing mirrors in One Laser Hydra

      Introduction The Hydra series of lasers come standard with a 2.5-inch focusing lens, with optional lenses available in 1.5-inch, 2.0-inch, and 4.0-inch sizes. This document will guide you on how to replace the different sizes of focusing lenses. ...

    • One Laser Firmware Upgrade Tutorial Hydra Series

      NOTE: Contact the manufacturer's technician for the latest version of the firmware programme.The HMI firmware (i.e. panel firmware) must be updated before updating the control motherboard. During the firmware update process, please ensure that the ...